Chinese look a like Little-M block
#11
Senior Member
RACING JUNKIE
Join Date: Sep 2007
Location: Belleville, IL
Posts: 658
Originally Posted by TheRabbit
Originally Posted by OneBadGMC
Originally Posted by Tod74
I worked for a company that had some stuff made in CHINA then unboxed it, washed it in a hot tank, stamped the part number on it with a pin stamp and "USA" and repacked it.
#12
Senior Member
DYNO OPERATOR
Join Date: Mar 2008
Location: New Orleans,La
Posts: 515
Originally Posted by Tod74
I worked for a company that had some stuff made in CHINA then unboxed it, washed it in a hot tank, stamped the part number on it with a pin stamp and "USA" and repacked it.
then spend $60 to check it out repack and advertise it for sale at $150 ,It's made in the USA
I don't agree ,but thats what i read
#13
It's called Foreign Trade. I fully understand we need to do some foreign trade and I agree it's a small world and we all need to work together and help each other, but all this is part of what's gotten us in this mess to begin with. We need to take care of ourselves FIRST. I agree, buy American, but that doesn't have the same meaning it did 25 years ago. The only way you can buy or help America(s) is to support your local businesses. Eventhough not all of their products will be "mad in the USA" you are helping put food on their table by spending $ with them.
#14
Junior Member
SHOW GUEST
Join Date: Dec 2006
Posts: 3
Chinese look a like Little-M block
I agree too much is made in China, but that isn't the point here.
I disagree about the knockoff engine blocks from PBM. Currently I have 2 SBC's that I am using with these aftermarket blocks from PBM. My engine builder got them for me in a 4.155" bore. These were ready to assembled. Everything speced out perfect! These have proven to be a value beyond my expectations. I would be more interested in hearing the findings of an independent test. Even more surprising is the web page link listed isn't functioning? To anyone out there, I would use these blocks over again, and recommend them to anyone interested. I look forward to your comments.
:x :x
I disagree about the knockoff engine blocks from PBM. Currently I have 2 SBC's that I am using with these aftermarket blocks from PBM. My engine builder got them for me in a 4.155" bore. These were ready to assembled. Everything speced out perfect! These have proven to be a value beyond my expectations. I would be more interested in hearing the findings of an independent test. Even more surprising is the web page link listed isn't functioning? To anyone out there, I would use these blocks over again, and recommend them to anyone interested. I look forward to your comments.
:x :x
#15
Senior Member
RACING JUNKIE
Join Date: Sep 2007
Location: Belleville, IL
Posts: 658
Re: Chinese look a like Little-M block
Originally Posted by jpcomeaux
I agree too much is made in China, but that isn't the point here.
I disagree about the knockoff engine blocks from PBM. Currently I have 2 SBC's that I am using with these aftermarket blocks from PBM. My engine builder got them for me in a 4.155" bore. These were ready to assembled. Everything speced out perfect! These have proven to be a value beyond my expectations. I would be more interested in hearing the findings of an independent test. Even more surprising is the web page link listed isn't functioning? To anyone out there, I would use these blocks over again, and recommend them to anyone interested. I look forward to your comments.
:x :x
I disagree about the knockoff engine blocks from PBM. Currently I have 2 SBC's that I am using with these aftermarket blocks from PBM. My engine builder got them for me in a 4.155" bore. These were ready to assembled. Everything speced out perfect! These have proven to be a value beyond my expectations. I would be more interested in hearing the findings of an independent test. Even more surprising is the web page link listed isn't functioning? To anyone out there, I would use these blocks over again, and recommend them to anyone interested. I look forward to your comments.
:x :x
How many miles or full passes are on the motors they are being used with?
Have you pulled the motors down since building and if so, what did the mains and cylinder bores look like?
How big of a cam were you using?
What did the lifter bores look like?
How high are you RPM'ing the motor?
All important things to take into consideration to say the least. Just because you threw it together and it fired up doesn't mean it's not junk.
#16
Senior Member
EXPERT BUILDER
Thread Starter
Join Date: Nov 2003
Location: NORTHEAST
Posts: 290
Re: Chinese look a like Little-M block
Originally Posted by jpcomeaux
I agree too much is made in China, but that isn't the point here.
I disagree about the knockoff engine blocks from PBM. Currently I have 2 SBC's that I am using with these aftermarket blocks from PBM. My engine builder got them for me in a 4.155" bore. These were ready to assembled. Everything speced out perfect! These have proven to be a value beyond my expectations. I would be more interested in hearing the findings of an independent test. Even more surprising is the web page link listed isn't functioning? To anyone out there, I would use these blocks over again, and recommend them to anyone interested. I look forward to your comments.
:x :x
I disagree about the knockoff engine blocks from PBM. Currently I have 2 SBC's that I am using with these aftermarket blocks from PBM. My engine builder got them for me in a 4.155" bore. These were ready to assembled. Everything speced out perfect! These have proven to be a value beyond my expectations. I would be more interested in hearing the findings of an independent test. Even more surprising is the web page link listed isn't functioning? To anyone out there, I would use these blocks over again, and recommend them to anyone interested. I look forward to your comments.
:x :x
What machines did you verify lifter bore and cylinder bore and cam tunnel locations with and son't tell me a vernier and what did the block brinell test at??
By the end of the week I should have some good photos and some reports on demensions.
Believe me those blocks are sent to Florida and a shop their is engraving PBM on the caps and blocks adding a stud kit line hone and finished machined.
The one we have the oil galley hole is to low int the bore and is not even square with the main line and you can see that by eye!!
I am sure you sonic tested right????????????
#17
Re: Chinese look a like Little-M block
Originally Posted by hink
Originally Posted by jpcomeaux
I agree too much is made in China, but that isn't the point here.
I disagree about the knockoff engine blocks from PBM. Currently I have 2 SBC's that I am using with these aftermarket blocks from PBM. My engine builder got them for me in a 4.155" bore. These were ready to assembled. Everything speced out perfect! These have proven to be a value beyond my expectations. I would be more interested in hearing the findings of an independent test. Even more surprising is the web page link listed isn't functioning? To anyone out there, I would use these blocks over again, and recommend them to anyone interested. I look forward to your comments.
:x :x
I disagree about the knockoff engine blocks from PBM. Currently I have 2 SBC's that I am using with these aftermarket blocks from PBM. My engine builder got them for me in a 4.155" bore. These were ready to assembled. Everything speced out perfect! These have proven to be a value beyond my expectations. I would be more interested in hearing the findings of an independent test. Even more surprising is the web page link listed isn't functioning? To anyone out there, I would use these blocks over again, and recommend them to anyone interested. I look forward to your comments.
:x :x
What machines did you verify lifter bore and cylinder bore and cam tunnel locations with and son't tell me a vernier and what did the block brinell test at??
By the end of the week I should have some good photos and some reports on demensions.
Believe me those blocks are sent to Florida and a shop their is engraving PBM on the caps and blocks adding a stud kit line hone and finished machined.
The one we have the oil galley hole is to low int the bore and is not even square with the main line and you can see that by eye!!
I am sure you sonic tested right????????????
#18
Junior Member
SHOW GUEST
Join Date: Dec 2006
Posts: 3
Chinese look a like Little-M block
I got these blocks about 6 months ago. They are circle track 434ci engines. The first one has about 1000 laps or so on it and is running great. The second we build as a backup, and simply haven't had to use it. We had the pan off at about 800 laps, everything looked great. We change the oil and cut the filter every week. We simply haven't had any problems. Sounds like somebody doesn't like the new kid on the block.
#19
Senior Member
EXPERT BUILDER
Thread Starter
Join Date: Nov 2003
Location: NORTHEAST
Posts: 290
Re: Chinese look a like Little-M block
Originally Posted by jpcomeaux
I got these blocks about 6 months ago. They are circle track 434ci engines. The first one has about 1000 laps or so on it and is running great. The second we build as a backup, and simply haven't had to use it. We had the pan off at about 800 laps, everything looked great. We change the oil and cut the filter every week. We simply haven't had any problems. Sounds like somebody doesn't like the new kid on the block.
And I beleive its Wheeler that is machining the blocks for PBM Correct???
#20
Senior Member
EXPERT BUILDER
Thread Starter
Join Date: Nov 2003
Location: NORTHEAST
Posts: 290
I just received call from a shop that has a PBM block and on some of the outter splayed bolt holes some of them go right into the water jacket. And they are going to send me this block for inspection to see for sure if they are the same castings or not.