diagram

Thread Tools
 
Old 05-27-2008, 02:45 PM
  #1  
kustomizer
Junior Member
SHOW GUEST
Thread Starter
 
Join Date: Nov 2003
Posts: 4
Default diagram

does anyone out there have a wiring diagram to wire a race car with relays and all any help would be appreciated thanxs scott
kustomizer is offline  
Old 05-27-2008, 05:49 PM
  #2  
mytmouz
Senior Member
RACING JUNKIE
 
mytmouz's Avatar
 
Join Date: May 2006
Location: Pelahatchie, MS
Posts: 1,004
Default

http://forums.racingjunk.com/viewtopic.php?t=4262
mytmouz is offline  
Old 07-11-2013, 03:23 AM
  #3  
jsims0540
Junior Member
SHOW GUEST
 
Join Date: Dec 1969
Posts: 3
Default Re: diagram

Originally Posted by kustomizer
does anyone out there have a wiring diagram to wire a race car with relays and all any help would be appreciated thanxs scott
jsims0540 is offline  
Old 07-11-2013, 03:26 AM
  #4  
jsims0540
Junior Member
SHOW GUEST
 
Join Date: Dec 1969
Posts: 3
Default Re: diagram

Originally Posted by jsims0540
Originally Posted by kustomizer
does anyone out there have a wiring diagram to wire a race car with relays and all any help would be appreciated thanxs scott





Did anyone every answer your question? I now have the same issue using a Painless Installation. fuse block, a 8 switch panel.
jsims0540 is offline  
Old 12-02-2013, 11:47 AM
  #5  
john910
Member
CRAFTSMAN
 
Join Date: Mar 2005
Posts: 59
Default diagram

if im going to install 3 relays should they be close to fan, pump. or close to switch? also what gauge wire is safe to supply power from battery to all 3 relays ex.10 or 12 gauge. thanks
john910 is offline  
Old 03-26-2015, 08:59 AM
  #6  
indcontrols
Junior Member
APPRENTICE
 
Join Date: May 2014
Posts: 18
Default

Always put the relay as close to the load (pump, fan, etc.) as practical - not just a myth... here's why...

The contact inside the relay must make (close) and break (open) the electrical load as it is turned on and off. The more current draw, the harder it is on the contacts to make and break. If the relay is 12 feet away, that 12 feet of wire has some electrical resistance... As the pump will draw the same amount of power (in watts), the relay must now also overcome the resistance of the wire length as well as the power to run the pump (ie; more current)... It must also break the larger current as well as dissipate the additional heat - shorter relay life...

As for the wire size, it is totally dependent on max operating (usually max occurs during starting) of the load / motor. If you're supplying more than one load, you must add them up - Below is a chart (credit* engineering toolbox) for 12v DC systems wire amperage ratings - This is based on PVC (crap wire) 75 and 90 degrees C rated wire common to automotive hook up wire.... I recommend going up a size once you figure it out !!! I use 150 or 200 degrees C rated wire (but that's cheating, I run a wire company...) You will notice that the wire run length must also be taken into consideration - for the reason I mentioned above. Be sure that the protection device (fuse, breaker, link) is sized according to what the wire can reliably hold...

American Wire Gauge (AWG)
Length
(feet) Current (amps)
5 10 15 20 25 30 40 50 60 70
15 16 12 10 10 8 8 6 6 4 4
20 14 12 10 8 8 6 6 4 4 4
25 14 10 8 8 6 6 4 4 2 2
30 12 10 8 6 6 4 4 2 2 2
40 12 8 6 6 4 4 2 2 1 1/0
50 10 8 6 4 4 2 2 1 1/0 1/0
60 10 6 6 4 2 2 1 1/0 2/0 2/0
70 10 6 4 2 2 2 1/0 2/0 2/0 3/0
80 8 6 4 2 2 1 1/0 2/0 3/0 3/0
90 8 4 4 2 1 1/0 2/0 3/0 3/0 4/0

Hope this helps !
indcontrols is offline  
Old 03-26-2015, 09:02 AM
  #7  
indcontrols
Junior Member
APPRENTICE
 
Join Date: May 2014
Posts: 18
Default

Chart didn't turn out well !! Here it is in readable form... http://www.engineeringtoolbox.com/am...uge-d_730.html
John[ATTACH=CONFIG]91[/ATTACH]
Attached Images
File Type: jpg
side shot.jpg (93.6 KB, 0 views)
indcontrols is offline  

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -